Get Ip For Mac Address

• Find Ip For Mac Address Cisco
• Get Ip For Mac Address Labels

How to Get all the IP and MAC. Step 1: Start Kali Linux or any Pentesting Distro. Step 2: Now find the Local IP Address,Open Terminal and type ifconfig and press enter. From the corresponding connection on which you are pickup inet address. Eth0 is LAN wlan0 is wifi. Step 3: Now Open 'netdiscover' from Kali Linux Menu or Terminal Netdiscover 0.3-pre-beta7 Active/passive arp. IP Address; MAC Address; Computer Description(If Available) Please save the below code in anyname.bat format and run it. It will output the results in a separate text file.:: This Windows Batch(CMD) File fetches All the Details of the Nearby PC's of Same VLAN (Upto 254 host's). The short video below demonstrates two 'manual' ways of retrieving the local IP and MAC address of your computer, as well as a single way to retrieve your public/external IP: Network connection details (local IP and MAC address). Command prompt – ipconfig and getmac (local IP and MAC address). Internet (public IP). GETMAC /s 192.168.1.1 – Get MAC Address by IP Address; GETMAC /s localhost – Get local MAC Address. Each network card in your computer has its own MAC address. A typical modern will normally have an Ethernet card, a WiFi card and a Bluetooth card. Each one will have its own MAC address.

In this article, I will take you through different ways to List/Get/Display/Find MAC Address in Linux. You might be aware of Ethernet Card/Network Card/NIC Controller which works at Network level and is responsible for communicating with other network devices in a Network Topology. It is used in Layer-2 Communication. You can find the usage of MAC address in wide range of Network Devices currently in use. This is typically in-line with IEEE 802 Network technologies.

What is MAC Address

MAC is abbreviated as Media Access Control. It is a unique 48 bit(6-byte) address assigned to a Network Interface. It is almost used in all the Network Devices which has network controller in it. It will always show in this form 00:07:Y7:1C:6L:03.

Find MAC Address in Linux

Also Read:25 Useful Linux SS Command Examples to Monitor Network Connections

Method 1: How to find MAC Address in Linux Using ifconfig command

If you want to check MAC Address of all the network interfaces in Linux using our traditional ifconfig command then you need to use ifconfig -a command as shown below.

NOTE:

Method 2: How to find an ethernet MAC Address in Linux Using ifconfig command

If you want to check the MAC Address of a specific network interface using ifconfig command then you need to use network interface name with ifconfig command as shown below. Here we are checking MAC Address of interface enp0s3 using ifconfig enp0s3 command.

NOTE:

Method 3: How to find MAC Address in Linux Using ip addr sh command

If you want to check the MAC address of all the network interfaces then you need to simply use ip addr sh command and check the MAC address from ether field as shown below.

Method 4: How to find an ethernet MAC Address in Linux using ip addr sh command

If you want to check the MAC address of some specific network interface then you need to use the interface name with ip addr sh command and check the MAC address from ether field as shown below. In this example we are checking MAC address of enp0s3 network interface.

Method 5: How to find MAC Address in Linux Using ip link show command

If you want to check the MAC address of all the network interfaces then you can use another useful ip link show command and check the MAC address from link/ether field as shown below.

Method 6: How to find an ethernet MAC Address in Linux using ip link show command

If you want to check the MAC address of some specific network interface then you need to use the interface name with ip link show command and check the MAC address from ether field as shown below. In this example we are checking MAC address of enp0s3 network interface.

Method 7: How to find MAC Address in Linux using ethtool command

You can also use another useful linux tool called ethtool to find MAC address in Linux as shown below. Here I am checking MAC address of my ethernet card enp0s3 using ethtool command hence you need to mention your Interface name before running below command.

Method 8: How to find MAC Address in Linux using Regex with ifconfig command

You can use a simple grep regular expression with ifconfig command to find the MAC Address of an ethernet card in Linux as shown below. Like above example, Here I am using regular expression on my System enp0s3 interface so you need to change and mention your interface name instead of enp0s3 before running below command.

Method 9: How to find MAC Address in Linux using SYS Files

If you want to check MAC address in Linux using SYS files you need to check network address file using below cat command. As mentioned below SYS file is a text file so its contents can always be seen through Linux cat command.

Find Ip For Mac Address Cisco

Method 10: How to find MAC Address in Linux using AWK Regex with ifconfig command

Get Ip For Mac Address Labels

You can also use AWK regular expression with ifconfig command to find MAC Address in Linux as shown below. Here we are grepping ether keyword from ifconfig command and then piping to awk to get first and second column output separated by tab.

Method 11: How to find MAC Address in Linux using Sed Regex with ifconfig command

Like above example, you can also use Sed Regular expressions with ifconfig command to find MAC Address in Linux as shown below.

Popular Recommendations:-

How to find an IP address when you have the MAC address of the device.

4 Steps total

Step 1: Open the command prompt

Click the Windows 'Start' button and select 'Run.' In the textbox, type 'cmd' and click the 'Ok' button. This opens a DOS prompt.

Step 2: Familiarize yourself with arp

Type 'arp' in the command prompt. This gives you a list of options to use with the arp command.

Step 3: List all MAC addresses

Type 'arp -a' in the command prompt. This lists a number of MAC addresses with the associated IP addresses. Since you have the MAC address, scroll down the list to find the associated IP address. The MAC address is shown in the 'Physical Address' column with the IP address in the 'Internet Address' column. An example of a table record is in Step 4.

Step 4: Evaluate results

The following is an example of ARP output. The first column is the IP address. The second column is the MAC address, and the third is the type of IP assigned--static or dynamic.

Internet address Physical Address Type

192.168.0.1 01-a3-56-b5-ff-22 static

References

• How to Use a MAC Address to Find an IP Address

16 Comments

• Datil
  Krizz Jan 21, 2013 at 10:36pm

  You've forgotten about one little thing: arp keeps mac<>ip association of recently contacted peers, so it's quite often not to find the mac<>ip association we're looking for, of machine that exists in the network. Prior to using arp -a it's wise to ping the host first.

• Habanero
  Twon of An Jan 21, 2013 at 11:24pm

  Used in conjunction with ping (thanks Krizz), this is a good basic walk through. I can't go wrong with these steps!

• Cayenne
  Syldra Jan 22, 2013 at 03:17pm

  I'm sorry but.. if the thing is to find the IP address from the MAC, how will you ping the host first ?

• Serrano
  Enzeder Jan 22, 2013 at 04:37pm

  I thought the aim of this exercise was to FIND an IP address. Doesn't using PING imply you already know the IP (or hostname) which makes ARP redundant? How do you PING a MAC?

  Assuming no IP or hostname info, I have used a portscanner (like LanSpy or Zenmap) to get MAC > IP info. Currently my preferred method if the device isn't listed in Spiceworks :-)

  There was a time when I was a baby admin and I didn't want to raise alarms by installing a scanner that I wrote a batch file (yes, that long ago) that PINGed every IP on a subnet, then immediately ran ARP redirecting output to a text file. But that depends on the device in question being set to respond to PING requests.

Method 8: How to find MAC Address in Linux using Regex with ifconfig command

You can use a simple grep regular expression with ifconfig command to find the MAC Address of an ethernet card in Linux as shown below. Like above example, Here I am using regular expression on my System enp0s3 interface so you need to change and mention your interface name instead of enp0s3 before running below command.

Method 9: How to find MAC Address in Linux using SYS Files

If you want to check MAC address in Linux using SYS files you need to check network address file using below cat command. As mentioned below SYS file is a text file so its contents can always be seen through Linux cat command.

Find Ip For Mac Address Cisco

Method 10: How to find MAC Address in Linux using AWK Regex with ifconfig command

Get Ip For Mac Address Labels

You can also use AWK regular expression with ifconfig command to find MAC Address in Linux as shown below. Here we are grepping ether keyword from ifconfig command and then piping to awk to get first and second column output separated by tab.

Method 11: How to find MAC Address in Linux using Sed Regex with ifconfig command

Like above example, you can also use Sed Regular expressions with ifconfig command to find MAC Address in Linux as shown below.

Popular Recommendations:-

How to find an IP address when you have the MAC address of the device.

4 Steps total

Step 1: Open the command prompt

Click the Windows 'Start' button and select 'Run.' In the textbox, type 'cmd' and click the 'Ok' button. This opens a DOS prompt.

Step 2: Familiarize yourself with arp

Type 'arp' in the command prompt. This gives you a list of options to use with the arp command.

Step 3: List all MAC addresses

Type 'arp -a' in the command prompt. This lists a number of MAC addresses with the associated IP addresses. Since you have the MAC address, scroll down the list to find the associated IP address. The MAC address is shown in the 'Physical Address' column with the IP address in the 'Internet Address' column. An example of a table record is in Step 4.

Step 4: Evaluate results

The following is an example of ARP output. The first column is the IP address. The second column is the MAC address, and the third is the type of IP assigned--static or dynamic.

Internet address Physical Address Type

192.168.0.1 01-a3-56-b5-ff-22 static

References

• How to Use a MAC Address to Find an IP Address

16 Comments

• Datil
  Krizz Jan 21, 2013 at 10:36pm

  You've forgotten about one little thing: arp keeps mac<>ip association of recently contacted peers, so it's quite often not to find the mac<>ip association we're looking for, of machine that exists in the network. Prior to using arp -a it's wise to ping the host first.

• Habanero
  Twon of An Jan 21, 2013 at 11:24pm

  Used in conjunction with ping (thanks Krizz), this is a good basic walk through. I can't go wrong with these steps!

• Cayenne
  Syldra Jan 22, 2013 at 03:17pm

  I'm sorry but.. if the thing is to find the IP address from the MAC, how will you ping the host first ?

• Serrano
  Enzeder Jan 22, 2013 at 04:37pm

  I thought the aim of this exercise was to FIND an IP address. Doesn't using PING imply you already know the IP (or hostname) which makes ARP redundant? How do you PING a MAC?

  Assuming no IP or hostname info, I have used a portscanner (like LanSpy or Zenmap) to get MAC > IP info. Currently my preferred method if the device isn't listed in Spiceworks :-)

  There was a time when I was a baby admin and I didn't want to raise alarms by installing a scanner that I wrote a batch file (yes, that long ago) that PINGed every IP on a subnet, then immediately ran ARP redirecting output to a text file. But that depends on the device in question being set to respond to PING requests.

• Pimiento
  christian.mcghee Dec 23, 2013 at 03:47am

  This does not work for any host on the other side of a router. Any hosts on the other side of the router will show the routers MAC address.

• Serrano
  @Greg Mar 11, 2014 at 03:11pm

  I realize this is an old topic, but someone like myself may be looking for an answer. I became admin of a network with little over 200 devices, which none of the cabling was mapped. I was told I was responsible for the cabling, so I began looking for a way other than toning out all the cables. I was fortunate to have Cisco switches and Windows Server 2008. I was able to use the Cisco Network Assistant to grab MAC addresses and the port number, then in DHCP on the Server 2008 I could find the MAC and corresponding IP. Furthermore I could also get the computer name from DHCP and correlate that to which user was on the machine using PDQ inventory to see who was logged in to the machine. Most of this of course depends on the devices being in use. I've been able to create an accurate map of about 90% of my network without touching the cables.

• Pimiento
  christopherblouch Jun 4, 2014 at 05:08pm

  I am interested in this thread, hopefully someone can help. There are 4 types of arp message: arp request, arp reply, rarp request, rarp reply. So, that being said, is it possible to manually send a rarp request? Sort of a arp based ping?There is arping, but we need rarping.. if it exists. Of course, I understand that I can't arp outside my default gateway, but if there is a rarp request, how is it used inside the local network? Thanks to whatever guru can explain what we're missing.

• Serrano
  Maxwell Brotherwood Jul 18, 2014 at 10:07am

  Great for finding an IP if you have the MAC address.

  My instance where I found this useful was after updating the firmware on a switch remotely via TFTP, the IP of the switch would change (making pinging redundant, obviously). Trying a network scan over Spiceworks or rescanning the single device would not update the IP and I needed an alternate way to find it.

  This method worked perfectly. Thank you. Hopefully this helps those trying to understand the purpose of this practice and how it was in-fact useful.

• Pimiento
  robertrobinson2 Aug 4, 2014 at 04:30pm

  I understand the issues in attempting to use a MAC address to locate a device from outside of its local network.
  What puzzles me is how Honeywell Total Connect does this with their WiFi connected thermostats. The hardware configuration is: a Honeywell WiFi thermostat that is WiFi connected to a Netgear N600 router which uses DHCP to assign an IP adddress. The router is connected to Comcast with a Motorola SB6120 modem. Comcast assigns a system wide (dynamic) IP. There is no static IP.
  On initial setup, a WiFi connection is first established between the thermostat and the router. The thermostat's MAC and CRC and a username and password are entered into the Total Connect software setup. It is then possible to read or set thermostat values using Total Connect Web pages.
  I know how to do this with a static IP or a DNS service that automatically tracks changes in dynamic IP addresses.
  Does anyone understand how this works with Total Connect?

• Tabasco
  Joe979 Sep 4, 2014 at 01:05pm

  This post was extremely helpful, thanks itdownsouth :) I used show interface to find MAC addresses on our switches (reason for this is poor network documentation and mis-labeled switchports and wall jacks..). I took the MAC addresses that I could not locate the hosts or ip addresses for, ran arp -a to list the address<>mac list, then one by one, nbtstat -A for each IP address I matched a MAC to from the unlabeled ports. Tedious, but found 5 or 6 now (seeing hexadecimal thoughts now though..).

• Tabasco
  Joe979 Sep 4, 2014 at 01:12pm

  By the way, the reason this is working great for me is the lack of routers -- all switches, so if you have only one subnet like we do, this will do -- otherwise, you will probably need to login to the router or switch on the other side of the router to find MAC address tables on the other networks. You may not be able to see them all on the local host, as far as arp -a on the local host, but looking up the arp or hosts tables on switches and routers could be a possible solution for those with multiple subnets.

• Jalapeno
  Jay196 Oct 21, 2014 at 03:28pm

  Use SuperScan to do a bulk ping of the entire network range. SuperScan 3 (I recommend) is a free tool by McAfee.

  Then use arp -a | Find '5c-d9-98' to get for example all ping nodes with a manufacturer of Asus.

• Datil
  WealthyEmu Mar 25, 2015 at 07:55pm

  There's also this:

  http://www.advanced-ip-scanner.com/

  It should be able to find most devices on the network. You can specify the range to scan and scan across subnets. I won't try to share all the features because quite frankly I don't know them all.

• Pimiento
  amiruli Jul 4, 2015 at 10:18am

  If you want you can ping the broadcast address to ping everyone on the network then do arp -a

• Pimiento
  chrisdahlkvist Nov 23, 2015 at 09:56am

  @RobertRobinson I'm the lead designer and project manager on the Honeywell systems.

  I can tell you exactly how I designed it. It's actually quite simple. Nothing is sent back to the unit. The unit is allowed access to the Internet via your setup and the router. As long as the unit has permission to make an outbound connection it will work. What happens is the unit makes a report to the server. If it needs to make a request then it gives the server a unique key. The server puts any needed data in an xml (readable) and the thermostat (or quite a few other devices) hits that URL a few seconds later (the device told the server where it would pick up that info).

  All your device needs is a simple read-only connection to the outside world. No need to download anything.
  It's a VERY simple process that I developed back in 1992 when the Interwebs were still pretty new to most people. There were many processes built off of this simple idea (it was pretty cutting edge when I first designed it). Store and forward, offline browsing, push technology, etc. all are based on this simple technology.

  Am I rich? Not even close. I was working on my PhD at the time and was hired by Honeywell to implement my design. I literally gave it away to the general public as is right.

  I hope that clears it up for you. If not, feel free to contact me for more information.

  Chris Dahlkvist
  chris@usarf.org

• prev
• 1
• 2
• next